Reactive waterproofing FPD
For the entire spectrum of building waterproofing - our system with PROLASTIC® 55Z.
Fast, flexible, efficient: Our PROLASTIC® 55Z reactive waterproofing reliably protects almost all building surfaces against water ingress. The innovative waterproofing combines the flexibility of polymer-modified bitumen thick coatings with the high adhesion of mineral waterproofing slurries - for maximum safety.
Fast construction progress guaranteed: The soil can be backfilled after just 16 hours, and interior surfaces are ready for screed or tiling work after just 4 hours.
The system structure in detail
| Substrate: Masonry according to DIN 1053, concrete, plaster (must be load-bearing, frost-free and clean) | |
| A. Primer | IMBERAL® Aquarol 10D |
| B. Waterproofing | PROLASTIC® 55Z |
| C. Reinforcement | IMBERAL® VE 89V |
System products at a glance
Your benefits
- Quickly rainproof and water pressure-tight
- Protective plates stick after 4 hours
- Backfill soil after 16 hours
- Highly flexible: crack bridging > 2 mm
- Suitable for all mineral substrates
- Resistant to frost, de-icing salt and UV radiation
- Waterproofing & bonding bridge in one
- Base and basement wall waterproofing in a single work step
- Radon-tight
Application areas
- Exterior basement waterproofing
- Waterproofing components in contact with the ground
- Safe against non-pressing and pressing water
- For vertical and horizontal surfaces indoors and outdoors
Processing instructions for new construction
1. Substrate preparation
1.1. Chamfering
Chamfer vertical and horizontal edges (concrete grinder)
1. Substrate preparation
1.2 Primer
(e. g. IMBERAL® Aquarol 10D)
1. Substrate preparation
1.3 Moisture protection
Optional moisture protection behind fillet (INTRASIT® RZ1 55HSP oder INTRASIT® DS1 54Z)
1. Substrate preparation
1.4 Concave fillet
Set the concave fillet (INTRASIT® RZ1 55HSP oder INTRASIT® FSM Winter 56Z)
1. Substrate preparation
1.5 Scratch coat
Optional scratch coat
2. Waterproofing
2.1 Waterproofing
First layer of waterproofing
2. Waterproofing
2.2 Reinforcement insert
Apply reinforcing insert to first waterproofing layer
2. Waterproofing
2.3 Waterproofing
Apply the second waterproofing layer
3. System protection
3.1 Insulation boards
Apply insulation boards to the waterproofing with board adhesive (IMBERAL® BEP-F 20B oder ÖKOPLAST® PK-2K 20B)
3. System protection
3.2 Protection and drainage mat
Protection and drainage mat (IMBERAL® Multidrain 89V) apply before waterproofing or insulation boards
Processing instructions for renovation
1. Substrate preparation
1.1 Waterproofing of old surfaces
Check whether old bitumen or tar waterproofing (friction test with cloth)
1. Substrate preparation
1.2 Expose
Remove old waterproofing from floor-wall connection (mechanically)
1. Substrate preparation
1.3 Priming
Prime exposed masonry (e.g. IMBERAL® Aquarol 10D)
1. Substrate preparation
1.4 Concave fillet
Set the concave fillet (INTRASIT® RZ1 55HSP or INTRASIT® FSM Winter 56Z)
1. Substrate preparation
1.5 Slurry
Apply a two-layer slurry coat to exposed masonry including the floor slab (INTRASIT® RZ1 55HSP oder INTRASIT® DS1 54Z)
1. Substrate preparation
1.6 Bonding bridge
Apply bonding bridge to old waterproofing (PROLASTIC® 55Z, IMBERAL® RSB 55Z, IMBERAL® 2K 20B depending on the waterproofing material used)
2. Waterproofing
2.1 Waterproofing
First layer of waterproofing
2. Waterproofing
2.2 Reinforcement insert
Apply reinforcing insert to the first waterproofing layer
2. Waterproofing
2.3 Waterproofing
Apply the second waterproofing layer
3. System protection
3.1 Insulation boards
Apply insulation boards to the waterproofing with board adhesive (IMBERAL® BEP-F 20B oder ÖKOPLAST® PK-2K 20B)
3. System protection
3.2 Protection and drainage mat
Protection and drainage mat (IMBERAL® Multidrain 89V) apply before waterproofing or insulation boards