Bitumen waterproofing with ÖKOPLAST®

Safe, economical and standard-tested.

Easy to apply and fast curing: our ÖKOPLAST® thick bitumen coatings reliably prevent water penetration and ensure long-lasting waterproofing of interior and exterior surfaces in contact with the ground. The standard-tested systems can be applied efficiently and are suitable for vertical and horizontal surfaces.

The system structure in detail

Substrate: Masonry according to DIN 1053, concrete and plaster (load-bearing, frost-free, free of separating substances)
A. PrimerIMBERAL® Aquarol 10D
B. Waterproofing & wear layerÖKOPLAST® 1K 20B
ÖKOPLAST® 2K 20B
C. Reinforcement insertIMBERAL® VE 89V

System products at a glance

A. Grundierung

IMBERAL® Aquarol 10D

Go to product

B. Abdichtung und Nutzschicht

ÖKOPLAST 1K 20B

Go to product

B. Abdichtung und Nutzschicht

ÖKOPLAST 2K 20B

Go to product

C. Verstärkungseinlage

VE Reinforcement insert 89V

Go to product

Flexible Mineralische Dickbeschichtung

PROLASTIC® 55Z

Go to product

Spezialmörtel

INTRASIT® DS1 54Z

Go to product

Renovierputz / Sanierputz

INTRASIT® RZ1 55HSP

Go to product

Your benefits

  • Easy to apply
  • Fast curing
  • Fiber-reinforced

Areas of application

  • Waterproofing of components in contact with the ground against splash water, ground moisture and non-accumulating seepage water
  • Protection against non-pressing water, accumulating seepage water and pressing water
  • Application on vertical and horizontal interior and exterior surfaces

Test certificates

Processing instructions for new buildings

1. Substrate preparation

1.1. Chamfering

Chamfer vertical and horizontal edges (concrete grinder)

1. Substrate preparation

1.2 Primer

(e. g. IMBERAL® Aquarol 10D)

1. Substrate preparation

1.3 Moisture protection

Optional moisture protection behind fillet (INTRASIT® RZ1 55HSP oder INTRASIT® DS1 54Z)

1. Substrate preparation

1.4 Concave fillet

Set the concave fillet (INTRASIT® RZ1 55HSP oder INTRASIT® FSM Winter 56Z)

1. Substrate preparation

1.5 Scratch coat

Optional scratch coat

2. Waterproofing

2.1 Waterproofing

First layer of waterproofing

2. Waterproofing

2.2 Reinforcement insert

Apply reinforcing insert to first waterproofing layer

2. Waterproofing

2.3 Waterproofing

Apply the second waterproofing layer

3. System protection

3.1 Insulation boards

Apply insulation boards to the waterproofing with board adhesive (IMBERAL® BEP-F 20B oder ÖKOPLAST® PK-2K 20B)

3. System protection

3.2 Protection and drainage mat

Protection and drainage mat (IMBERAL® Multidrain 89V) apply before waterproofing or insulation boards

Verarbeitungshinweise bei der Sanierung

1. Substrate preparation

1.1 Waterproofing of old surfaces

Check whether old bitumen or tar waterproofing (friction test with cloth)

 

1. Substrate preparation

1.2 Expose

Remove old waterproofing from floor-wall connection (mechanically)

1. Substrate preparation

1.3 Priming

Prime exposed masonry (e.g. IMBERAL® Aquarol 10D)

1. Substrate preparation

1.4 Concave fillet

Set the concave fillet (INTRASIT® RZ1 55HSP or INTRASIT® FSM Winter 56Z)

1. Substrate preparation

1.5 Slurry

Apply a two-layer slurry coat to exposed masonry including the floor slab (INTRASIT® RZ1 55HSP oder INTRASIT® DS1 54Z)

1. Substrate preparation

1.6 Bonding bridge

Apply bonding bridge to old waterproofing (PROLASTIC® 55Z, IMBERAL® RSB 55Z, IMBERAL® 2K 20B depending on the waterproofing material used)

2. Waterproofing

2.1 Waterproofing

First layer of waterproofing

2. Waterproofing

2.2 Reinforcement insert

Apply reinforcing insert to the first waterproofing layer

2. Waterproofing

2.3 Waterproofing

Apply the second waterproofing layer

3. System protection

3.1 Insulation boards

Apply insulation boards to the waterproofing with board adhesive (IMBERAL® BEP-F 20B oder ÖKOPLAST® PK-2K 20B)

3. System protection

3.2 Protection and drainage mat

Protection and drainage mat (IMBERAL® Multidrain 89V) apply before waterproofing or insulation boards