INTRASIT® Poly-C1 54Z
- Sealing compound for waterproofing in building and underground construction, 1.5 - 5 mm
- for waterproofing in building construction and civil engineering on concrete, plaster and masonry, for alternative waterproofing under tiled surfaces indoors and outdoors
- for horizontal waterproofing under rising walls
- as intermediate and spray water waterproofing, as well as bonding bridge
- for full-surface waterproofing of concrete surfaces, also in areas in contact with the ground and as basement waterproofing in accordance with DIN 18533 W1-E, W4-E
- for waterproofing building bases and for bonding perimeter insulation boards in the splash water area
- as a carbonation brake for concrete components exposed to the elements
- resistant to the aggressive substances normally found in soil
- crack-bridging
- waterproof
Pictograms
APPLICATION LOCATION
outside: floor, wall
inside: Floor, wall
PROCESSING TEMPERATURE
(air, surroundings, product)
min. + 5°C to max. + 30°C
PERSONAL PROTECTIVE EQUIPMENT:
Safety goggles und
gloves
MIXING:
Component ratio: a 1 : b 3 kg
APPROACH:
Spiral stirrer
600 revolutions / minute, 3 minutes
PROCESSING TIME:
1,5 hours
TOOLS / ACCESSORIES:
Brush
CLEANING THE TOOLS
Water
STORAGE
Duration: 12 months
Conditions: dry, frost-free
DISPOSEL COMPANY
Interseroh Transportverpackung
20447
Features
Properties
INTRASIT® Poly-C1 54Z is a pasty, well-adhering polymer-cement-based waterproofing compound. After mixing the two components, the result is a PCC mortar that is easy to trowel and spreadable after adding 1 % water. INTRASIT® Poly-C1 54Z cures stress-free even in layer thicknesses of 5 mm.- resistant to the aggressive substances normally found in soil
- crack-bridging
- waterproof
- flexible at low temperatures
- frost and de-icing salt-resistant
- universal use
- can be plastered over
Applications
- Concrete, plaster, masonry
- Damp and wet rooms
- Balconies, terraces, arcades
- Waterproofing of concrete surfaces in areas in contact with the ground
Composition
- Liquid component: Polymer dispersion, additives
Processing
Substrate
Properties/tests
- The substrate must be firm, level, load-bearing, free of oil, grease, frost, dust, dirt, mortar residue and loose particles.
- Masonry must be fully jointed.
Pretreatment
- Pre-wet substrate evenly, matt damp.
- Break corners and edges, create coving.
- Minor unevenness can be evened out with INTRASIT Poly-C1 54Z using a scratch coat.
- Brush or spray VESTEROL TG 10D onto gypsum plaster and gypsum plasterboard as a primer.
Use IMBERAL Aquarol 10D as a primer on all absorbent, mineral substrates
.
Processing
Processing
- Mix INTRASIT Poly-C1 54Z with a slow-running stirring tool (400 to 600 rpm). Stir for 2 to 3 minutes. To do this, pour in the entire liquid component and add the powder while stirring.
- For a slurry consistency: stir approx. 0.2 l water (1 %) into the ready-mixed sealing slurry.
- INTRASIT Poly-C1 54Z can be applied by brush, trowel or spraying. Ensure that the waterproofing compound is applied evenly. Avoid trowel marks in the material surface.
- The maximum layer thickness per application is 5 mm.
- To achieve a homogeneous, even and non-porous sealing layer, we recommend applying the sealing slurry in 2 coats.
- Allow a drying time of 3 to 5 hours between coats, depending on weather conditions.
Cleaning the tools
- Clean tools immediately after use with water.
Notes
- Guidelines are DIN 18533 for structural waterproofing and DIN 1053 for masonry construction.
- Maintain a processing temperature of +5 °C to +30 °C.
- Premature skin formation is to be expected in the event of sunlight, increased temperature and wind movement. Shading precautions are recommended.
- Only use on dry or matt damp substrates.
- Coarse trowel marks in the surface and material accumulations must be avoided.
- Protect from mechanical stress until sufficiently cured. Provide protective layers in accordance with DIN 18533.
Technical data
| Technical specification | EN 14891 |
| Colour | grey |
| Processing temperature | +5°C to +30°C |
| workable time | approx. 1 – 2 hours |
| Load-bearing capacity | after approx. 24 hours |
Article
| Article No. | Article Abbreviation | GTIN/EAN 4004637 | Package size |
|---|---|---|---|
| 40303 | Poly-C1 54Z grey | - 40303 2 | 20 kg/set |
Downloads
| Technical data sheet INTRASIT Poly-C1 54Z | download | |
| Safety data sheet INTRASIT Poly-C1 54Z | download | |
| Declaration of performance INTRASIT Poly-C1 54Z | download | |
| abP P-22-MPANRW-11396-25-1 INTRASIT Poly-C1 54Z (MDS) | download | |
| Environmental Product Declaration (EPD) for modified mineral mortars – Group 3 | download | |
| EMICODE Licence INTRASIT Poly C1 54Z | download | |
| Brochure INTRASIT® Poly-C1 54Z Structural waterproofing | download |